Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Torrance?
Gate installation in Torrance typically runs between $1,850 and $7,900 for a standard residential driveway gate, with most homeowners spending around $3,200 to $4,600 for a single swing gate with a motor. A basic Pedestrian Gate without automation starts around $950, while a full custom iron driveway gate with dual operators and intercom can reach $12,000 or more. The final number depends on gate material, width, whether you’re adding a motor, and what’s already on the property.
These figures reflect what we see across Torrance neighborhoods like Southwood, Hollywood Riviera, Old Torrance, and Walteria in 2026. A wood gate costs less than wrought iron. A single swing costs less than a sliding gate. And adding automation to an existing gate is a different job entirely from installing a new gate and motor together.
Gate Installation Cost Breakdown (2026)
Here’s what gate installation components cost in the Torrance market as of 2026. These are line-item ranges we quote from daily, not national averages pulled from a database.
| Component | Typical Torrance Cost Range | Notes |
|---|---|---|
| Walk gate (single, wood or steel frame) | $950 – $2,400 | No motor, basic latch hardware |
| Driveway gate – wood (single swing) | $1,850 – $4,200 | Redwood or cedar, includes posts and hinges |
| Driveway gate – steel/aluminum (single swing) | $2,400 – $5,800 | Powder-coated finish, lighter than iron |
| Driveway gate – wrought iron (single swing) | $3,200 – $7,900 | Custom fabrication, heavier, classic look |
| Driveway gate – wrought iron (double swing) | $5,400 – $12,500 | Two leaves, wider opening, heavier posts |
| Gate motor / operator (swing) | $850 – $1,900 | Includes arm, control board, receiver |
| Gate motor / operator (slide) | $1,100 – $2,400 | Requires slide track or cantilever system |
| Gate installation labor | $600 – $1,800 | Typically one to two days for full install |
| Concrete pad / post footings | $250 – $700 | Per post, depends on soil and depth |
| Electrical run to gate | $400 – $1,300 | Trenching, conduit, connection to panel |
| Intercom / keypad entry system | $350 – $1,100 | Basic keypad to multi-tenant intercom |
| Vehicle loop detector (exit wand) | $300 – $700 | Detects a car leaving, opens gate automatically |
What drives the numbers up or down: material weight, gate width, whether posts need to be set in existing concrete or fresh footings, and how far the electrical has to travel from the panel. In older Torrance neighborhoods like Seaside and Marble Estates, we often run into narrow parkways that make slide gate retrofit expensive because there isn’t room for the track run.
What About Replacing an Existing Gate?
If you already have posts set and a gate that’s just worn out, replacement costs drop significantly. Swapping an existing swing gate for a new one in Torrance typically runs $1,200 to $3,800 depending on material, since the posts, footings, and electrical are already in place. You’re paying for the gate, hinges, removal of the old gate, and installation labor. If the posts themselves are rusted or leaning, that’s a different scope: expect to add $700 to $1,600 for new posts and concrete.
What Affects Gate Installation Pricing in Torrance
Six factors move the price more than anything else. Here’s what we account for when we write a quote for a Torrance property.
- Gate material. Wood is the least expensive and looks right at home on the tree-lined streets in Southwood Riviera, but it warps and sags over time. Wrought iron costs more up front and holds its shape for decades. Powder-coated steel sits in the middle on cost and durability.
- Gate width and weight. A 10-foot single driveway gate is a different job from a 16-foot double gate. Wider and heavier gates need larger posts, heavier hinges, and a stronger motor. In hillside sections of Hollywood Riviera, the slope adds wind load that a flat lot in central Torrance won’t see.
- Automation. A manual gate is less expensive than an automated one, but almost every driveway gate we install in Torrance includes a motor. The operator brand matters: LiftMaster and FAAC parts are easy to source, while Viking and Ghost Controls operators cost a bit more for the hardware.
- Post and footing condition. If your existing posts are plumb and solid, you save $700 to $1,600 on new concrete and post work. If not, we’re digging footings. Torrance has a mix of sandy loam near the coast and harder clay inland, which affects how deep we go and how much concrete we pour.
- Electrical access. Running power to a gate that’s 80 feet from the panel with a sidewalk in between is more expensive than a gate 15 feet from an outdoor outlet. We trench carefully and restore the ground, but the labor is what it is.
- Permit requirements. The City of Torrance requires a permit for some gate installations, particularly automated driveway gates in front of a residence. Permit fees and inspection scheduling add time and cost. We handle the paperwork, but the city’s fee schedule is outside our control.
Is It Cheaper to Install a Gate Yourself?
Straight answer: you’ll save labor costs, which run $600 to $1,800 on a typical Torrance install. And you’ll spend more on mistakes. We’ve been called to fix gates where a homeowner set posts without checking the plumb line, wired a swing operator backward, or poured a footing that cracked within a year because it was too shallow for the soil.
The trade-off isn’t really about skill. It’s about time, tools, and tolerances. A gate post that’s off by half a degree translates to a gate that sags and drags within months. A motor that’s mounted with the wrong clearance burns out the limit switch. If you’re comfortable with concrete work, electrical, and a level, a manual walk gate is a reasonable weekend project. An automated driveway gate is not the place to learn.
For most Torrance homeowners, the math favors hiring a crew that does this every day. Our installers set posts, hang the gate, wire the motor, and program the remotes in one to two days. The written price you get before work starts is the price you pay. No re-quoting at the door.
How Long Does Gate Installation Take in Torrance?
A standard single swing driveway gate with automation takes one full day. A double gate or a slide gate with concrete work takes two. Custom wrought iron fabrication adds one to three weeks for the gate to be built before installation day arrives.
Here’s the sequence we follow:
- Site walk and written quote (Day 1). We measure the opening, check post condition, locate the electrical panel, and check the grade. You get a written price before any work starts, per the Garrison Standard.
- Permit pull (Days 2 to 10). If the City of Torrance requires a permit for your automated gate, we file it. This timeline is set by the city, not by us.
- Post setting and concrete (Day 11 or on approval). We dig footings, set posts, and pour concrete. Most concrete needs one to two days to cure before we hang a gate on it.
- Gate hang and motor install (1 day). We mount the gate, install the operator, wire the control board, and run the remotes and keypad.
- Testing and walkthrough (same day). We cycle the gate, set the limits, test the safety sensors, and show you how the keypad, remotes, and manual release work.
Weather in Torrance rarely delays a job the way it does in other counties. June gloom doesn’t stop concrete work, and we don’t shut down for light rain. High wind during Santa Ana season can push back a gate hang because a swinging door acts like a sail until it’s fully secured.
How to Save on Gate Installation
The biggest savings come from reusing what’s already there. If your posts are solid, keep them. If your existing motor still runs and you only need a new gate, keep the motor and replace the gate. Here’s what else moves the number down:
- Choose the right material for the job, not the street. A powder-coated steel gate holds up as well as iron on Torrance’s coastal air at roughly 40 to 50 percent less cost. If you want the iron look, get iron. If you want durability and a clean line, steel is a smarter buy.
- Standardize your gate width. A 10-foot or 12-foot single swing gate is far less expensive than a custom 14-foot opening. If your driveway will accommodate it, stay within standard dimensions.
- Install a keypad instead of an intercom. A basic keypad entry is $350 to $600 installed. A multi-tenant intercom system runs $800 to $2,500. If you’re gating a single-family driveway, you probably don’t need the intercom.
- Skip the fancy finish. Custom hand-forged details, elaborate scrollwork, and specialty powder coats all add cost. A clean, simple design is less expensive and easier to maintain.
- Bundle work. If you’re also repairing or replacing the gate motor, doing both at once costs less than two separate service visits. You pay one mobilization, one set of permits, one crew day.
And on the topic of estimates: ours are free. Call (424) 757-9824 and we’ll send a technician to walk your property, measure the opening, and hand you a written price with no obligation. The number on that paper is the number you pay if you decide to move forward.
Gate Installation in Torrance: What to Expect From Carver
We’re a gate-only shop. Not a handyman service that sometimes hangs gates, not a general contractor that subs gate work out. Gate installation and gate motor repair are what we do, every day, across Torrance and the South Bay. Our Gate Installation in Torrance service covers everything from a simple walk gate to a double swing driveway gate with full automation.
Every Carver Gate Repair location operates under the Garrison Standard, which has been our operating rule since 2008. It means three things on every job: a written price delivered before any work starts, a background-checked technician in uniform who shows up on time, and a written one-year guarantee on the work. If something isn’t right within that year, we come back and make it right at no charge. No argument, no re-inspection fee, no fine print.
We work on nine motor brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters because a gate is only as reliable as the motor that runs it, and the motor is only as reliable as the technician who wires it. Our crew has the right parts and the right know-how for whatever system you already have, which saves time and money compared to a generalist who has to order parts and guess at wiring diagrams.
Lonnie Burke runs the operation out of our Torrance location, and he holds every installed gate to the same standard: plumb posts, clean welds, neat wire runs, and a gate that cycles smoothly on the day we leave and a year later. That’s the Garrison Code: do the job once, do it right, and stand behind it in writing.
FAQs – Gate Installation Cost
How much does a gate motor cost to install in Torrance?
A gate motor or operator installation in Torrance runs $850 to $2,400, depending on whether it’s a swing or slide operator and whether the electrical is already at the gate. A basic swing operator from LiftMaster or FAAC installed with new wiring and remotes typically lands near $1,200 to $1,800. If you need the operator installed and a gate installed, both together are more cost-effective than two separate visits. Call (424) 757-9824 for an exact quote on your system.
Is it cheaper to repair a gate or replace it?
Repair is almost always cheaper when the gate itself is structurally sound. A sagging hinge, a bad limit switch, a worn wheel on a slide gate, or a dead circuit board can usually be fixed for $150 to $600. Replacement only makes sense when the gate frame is rusted through, the posts are failing, or you’re planning to change the gate style entirely. In Torrance’s coastal air, steel gates near the beach can rust faster than inland homes, so we look at the frame before recommending repair versus replacement.
Can you install a gate the same week?
In most cases, yes. Stock steel and aluminum gates can usually be installed within a week of your site visit. Custom wrought iron fabrication takes longer because the gate is built to your opening and finish, typically two to four weeks from order to install. Call (424) 757-9824 and we’ll tell you the current lead time before you commit to anything.
Do I need a permit to install a gate in Torrance?
Automated driveway gates in Torrance often require a permit, particularly when the gate is in front of a residence or near a sidewalk. A manual walk gate inside a fence line typically doesn’t. We handle the permit filing and scheduling, but the City of Torrance sets the fees and review timeline. We’ll tell you during the site walk whether your project triggers the requirement.
How much does a wooden driveway gate cost in Torrance?
A wooden driveway gate in Torrance runs $1,850 to $4,200 for a single swing, including posts and hardware. Redwood and cedar are the standard choices here because they handle the marine layer without rotting as fast as pine. Wood gates need more maintenance than steel or iron, particularly on west-facing lots that catch the afternoon sun and salt air. If you’re comparing, a steel gate at $2,400 to $5,800 is the lower-maintenance alternative.
Can Carver install a gate and motor on the same day?
Yes, in most cases. A stock single swing gate with a motor and keypad is a one-day install. We set the posts, hang the gate, wire the operator, program the remotes, and walk you through the system before we leave. You get a written price before any work starts, and the install carries a one-year written guarantee.
Get a Written Gate Installation Price in Torrance
If you’re considering a gate for your driveway, call (424) 757-9824. We’ll schedule a site walk, measure the opening, check your electrical, and hand you a written price before any work begins. No estimate that grows at the door, no surprises on the invoice. That’s the way we’ve run things since 2008, and it’s what the Garrison Standard requires.
Back to our home page for the full list of services.
Pricing reflects the Torrance market as of 2026. Carver Gate Repair Torrance offers free estimates – call (424) 757-9824.
Written by Lonnie Burke, Owner at Carver Gate Repair Torrance, serving Torrance since 2008.
What Our Customers Say
"Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A."Added a battery backup so the gate works during a power outage. Easy to use."
- Mitch L."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H.